Posted on December 23, 2018

E151FPB DRIVER

This is the time to really test your basic electronics skill because you now know at which area the fault is and you just have to use your skills to locate the exact bad component. When the power is on the light bulb still do not lit and the sound still could be heard. Just like flyback transformer, the best testing equipment to test Fet and other components is actually the equipment itself because it runs on full operating voltage, frequency, signal and etc. It was quite challenging to troubleshoot this kind of problem where you are hundred percent sure that the primary side is giving problem yet you could not find out the culprit. However this monitor boards looks perfectly okay.

Uploader: Zolonris
Date Added: 14 November 2015
File Size: 57.71 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 44581
Price: Free* [*Free Regsitration Required]

You could use this method but first you must confirm that the secondary filter capacitors, TL adjustable precision shunt regulator ic, optoisolators e1511fpb components surrounding the optoisolator is working before you proceed to use the light bulb.

Wishing you all the best and happy repairing! From experienced I do encountered semiconductor components breakdown when under full operating voltage.

Dell E151FPb

As usual whenever the mainboard and power board were exposed, I would look for any bulged e511fpb, darkened area, a loosen connector and etc. I began to check again the defective 2N fet with my analog meter and peak electronic atlas component analyzer and the result is still the same-tested good!

What you have just learned from here was that if all the suspected components tested good, the only way to reveal the truth is to direct replace the parts. This is the time to really test your basic electronics skill because you now know at which area the fault is and you e151fp have to use your skills to locate the exact bad component. When the power is on the light bulb still do not lit and the sound still could be heard. The moments I have replaced this fet and power on, the bulb immediately light up.

New Drivers  ASUS A7NBX ETHERNET DRIVER

However this monitor boards looks perfectly okay.

Dell E151FPB LCD Monitor

A defective component in either primary or secondary side could cause low output voltage. Plasma TV Repair Ebook. Just like flyback transformer, the best testing equipment to test Fet and other components is actually the equipment itself because it runs on full operating voltage, frequency, signal and etc. I could not w151fpb it was this faulty fet that causes all the output voltages to drop!

It was quite challenging to troubleshoot this kind of problem where you are hundred percent sure that the primary side is giving problem yet you could not find out the culprit. Guess what, you would not believe what have I just discovered-a defective 2N fet! Removing the fuse as shown in the photo and connect the bulb between the supply line and the cold ground could tell which section is giving problem. There were not much components in the primary side, and you could easily check all of them in less than 20 minutes.

After checking all the components I was surprised that all of them tested okay. If the LCD monitor designed to run on 18 or 24 volts then you could use a light bulb from the big trailer.

New Drivers  CIRQUE GLIDEPOINT DRIVER

Dell EFPb – LCD monitor – 15″ Overview – CNET

In fact this is good news to us because we know what e51fpb next step that we should make. Hope you enjoy this article and more good articles to come everyday! Now we could use a 12 volt automobile brake light bulb to test at which section that is causing the low voltage output problem.

Dell Efpb LCD monitor came in with the complaint of no power but upon carefully look at the LCD you could see a very light blur white flashes across the screen and the power LED is not e151fppb.

Removing the cover was a bit easy compared to other models. How To Test Electronics Components.

Since I had checked all f151fpb components and could not locate the fault, the only way that E151fpn could do is to direct replace the semiconductor devices such as the diodes, scr, fet, and transistors.

When I measure the 12 volts line with a digital multimeter, the readout was about 7- 8 volts which was very unusual. One by one of the semiconductor components I replaced and power on each time I had changed it to see if the bulb light up or not.